ETSI European Telecommunications Standards Institute

F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
secretariat@etsi.fr

Web Site http://www.etsi.org

For a status of all the work relating to Short Range Devices visit Short Range Devices

EN 300 220-1 V1.3.1 (2000-9) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Technical characteristics and test methods for radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW; Part 1: Parameters intended for regulatory purposes

Foreword

This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document, together with ETS 300 683, is intended to become a Harmonized EMC Standard which is intended to be published in the Official Journal of the European Communities referencing Council Directive 89/336/EEC "Council Directive on the approximation of the laws of the member States relating to electromagnetic compatibility ("the EMC Directive"). The technical parameters which are relevant to the EMC Directive are listed in annex E. The present document consists of two parts as follows:

Part 1: "Parameters intended for regulatory purposes";
Part 2: "Supplementary parameters not intended for regulatory purposes".

Clauses 1 and 3 provide a general description on the types of equipment covered by the present document and the definitions and abbreviations used. Clause 4 provides a guide as to the number of samples required in order that type tests may be carried out, and any markings on the equipment which the applicant should provide.

Clause 7 gives the maximum measurement uncertainty values.

Clauses 8 and 9 specify the spectrum utilization parameters which are required to be measured. These are the maximum limits which have been chosen to minimize harmful interference to other equipment and services. The clauses provide details on how the equipment should be tested and the conditions which should be applied.

Annex A provides specifications concerning radiated measurements.

Annex B contains specifications for adjacent channel power measurement arrangements.

Annex C provides information on the spectrum analyser specification.

Annex D is a graphical representation of subclause 4.1, referring to the presentation of equipment for testing purposes.

Annex E provides information on the parameters relevant to the EMC Directive.

National transposition dates
Date of adoption of this EN: 24 October 1997
Date of latest announcement of this EN (doa): 28 February 1998
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 1998
Date of withdrawal of any conflicting National Standard (dow): 31 August 1998

Scope

The present document covers the minimum characteristics considered necessary for Short Range Devices (SRD) in order to make the best use of the available frequencies. The term "The present document" refers to EN 300 220-1 only.

The present document contains the technical characteristics for radio equipment referencing CEPT/ERC Decisions and Recommendation CEPT ERC/Recommendation 70-03 [1].

The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It is a product family standard which may be completely or partially superseded by specific standards covering specific applications.

The present document applies to short range devices:

- either with a Radio Frequency (RF) output connection and/or with an integral antenna;
- for alarms, identification, telecommand, telemetry, etc., applications;
- with or without speech;
- operating on radio frequencies between 25 MHz and 1 000 MHz, with power levels up to 500 mW, radiated or conducted.

The parameters in clauses 8 and 9 of the present document are considered as spectrum utilization parameters. It is intended that these parameters will be measured by an accredited test laboratory for the purpose of type testing and approval.

The present document covers fixed stations, mobile stations and portable stations. In the present document basic requirements are given for the different frequency bands, channel separations etc., where appropriate.

All types of modulation are covered, in the present document, provided the requirements of subclauses 8.5 or 8.6, whichever is applicable, are met.

The radio equipment, covered by the classification SRD is divided into several classes based on maximum output power (see table 1). The class designation is based on CEPT/ERC Recommendation 70-03 [1].

Table 1

For non-harmonized parameters, national regulatory conditions can apply regarding the type of modulation, channel/frequency separations, maximum transmitter output power/effective radiated power, duty cycle, equipment marking and the inclusion of an automatic transmitter shut-off facility as a condition of the issue of an individual or general licence, or, as a condition of use under licence exemption. The extreme temperature ranges are fixed and are given in subclause 5.4.1.2.

The present document does not require measurements for radiated emissions below 25 MHz.

Additional standards or specifications can be required for equipment such as that intended for connection to the Public Switched Telephone Network (PSTN).

EN 300 220-2 V1.3.1 (2000-9) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Technical characteristics and test methods for radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW; Part 2: Supplementary parameters not intended for regulatory purposes

Foreword

This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum matters (ERM).

The technical parameters which are relevant to the EMC Directive are listed in annex B.

The present document consists of two parts as follows:

Part 1: "Parameters intended for regulatory purposes";
Part 2: "Supplementary parameters not intended for regulatory purposes".

This part specifies supplementary parameters for specific applications not related to effective use of the spectrum.

Annex A provides specifications concerning social alarm systems.

National transposition dates
Date of adoption of this EN: 24 October 1997
Date of latest announcement of this EN (doa): 28 February 1998
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 1998
Date of withdrawal of any conflicting National Standard (dow): 31 August 1998

Scope

The present document covers the minimum characteristics considered necessary for Short Range Devices (SRD) in order to make the best use of the available frequencies. The term "The present document" refers to EN 300 220-2 only. These parameters specified in this part are not intended to be measured for regulatory purposes. However, they are provided to give guidance to manufacturers and users regarding reasonable reliability of the radio link and performance of the receiver.

The present document contains the technical characteristics for radio equipment referencing relevant CEPT/ERC Decisions and Recommendation CEPT ERC/Recommendation 70-03 [1].

The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It is a product family standard which may be completely or partially superseded by specific standards covering specific applications.

The present document applies to short range devices:

- either with a Radio Frequency (RF) output connection and/or with an integral antenna;
- for alarms, identification, telecommand, telemetry, etc., applications;
- with or without speech;
- operating on radio frequencies between 25 MHz and 1 000 MHz, with power levels up to 500 mW, radiated or conducted.

The present document covers fixed stations, mobile stations and portable stations. In the present document basic requirements are given for the different frequency bands, channel separation etc., where appropriate.

The present document does not require measurements for radiated emissions below 25 MHz.

Additional standards or specifications may be required for equipment such as that intended for connection to the Public Switched Telephone Network (PSTN).

EN 300 328 - 1: V 1.2.2 July 2000 Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques

Foreword

This European Telecommunication Standard (ETS) has been produced by the Radio Equipment and Systems (RES) Technical Committee of the European Telecommunications Standards Institute (ETSI).

Annex A provides additional requirements concerning radiated measurements.

Annex B contains normative specifications for the adjustment of the measurement equipment and of the equipment to be measured in order to achieve correct results.

Annex C provides a Bibliography.

Transposition dates
Date of adoption of this ETS: 8 November 1996
Date of latest announcement of this ETS (doa): 28 February 1997
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 August 1997
Date of withdrawal of any conflicting National Standard (dow): 31 August 1997

Introduction

Wideband radio data transmission systems are rapidly being introduced into a variety of commercial and industrial applications and the technology employed by these systems is still developing.

This ETS may be used by accredited test laboratories for the assessment of the performance of the equipment. The performance of the equipment submitted for type testing should be representative for the performance of the corresponding production model. In order to avoid any ambiguity in that assessment, this ETS contains instructions for the presentation of equipment for type testing purposes (clause 4), testing conditions (clause 6) and methods of measurement (clause 7).

This ETS assumes that:

- the type test measurements performed in an accredited test laboratory in one CEPT country would be accepted by the Type Approval Authority in another country provided that the national regulatory requirements are met (see CEPT Recommendation T/R 71-03 [3]);

- if equipment available on the market is required to be checked it would be tested in accordance with the methods of measurement specified in this ETS.

Scope

This European Telecommunication Standard (ETS) covers equipment referred to in CEPT Recommendation T/R 10-01 [1]. This ETS covers the minimum technical characteristics for radio data transmission equipment having the following technical parameters:

- wideband radio modulation techniques;
- aggregate bit rates in excess of 250 kbits/s;
- operation in the 2,4 to 2,483 5 GHz Industrial, Scientific and Medical (ISM) band;
- effective radiated power of up to -10 dBW (100 mW);
- power density of up to -10 dBW (100 mW) per 100 kHz for frequency hopping modulation;
- power density of up to -20 dBW (10 mW) per 1 MHz for other forms of spread spectrum modulation.

This ETS only addresses the transceivers, transmitters and receivers of equipment offered for testing.

The equipment offered for testing may be used in fixed, mobile or portable applications, e.g.:
- stand-alone radio equipment with or without their own control provisions;
- plug-in radio devices intended for use with or within a variety of host systems, e.g. personal computers, hand-held terminals, etc.

The equipment may be fitted with integral antennae and/or antenna connectors.

CEPT Recommendation T/R 10-01 [1] defines the total power and power density limits for systems using spread spectrum modulation together with a minimum aggregate bit rate of 250 kbits/s. The Recommendation does not address the details of these modulation techniques. Therefore, this ETS does not cover the design or operation of the equipment being tested but describes a common set of measurements to be applied to various types of such equipment, including those employing Frequency Hopping Spread Spectrum (FHSS) modulation and Direct Sequence Spread Spectrum (DSSS) modulation.

CEPT Recommendation T/R 10-01 [1] specifies that spread spectrum modulation be used and it gives power density values for FHSS and DSSS modulation. This ETS specifies the minimum technical parameters of FHSS modulation such that it can be clearly differentiated from other types of modulation, including DSSS modulation.

CEPT Recommendation T/R 01-04 [2] defines limits of spurious emissions for a variety of radio equipment; these limits are used in this ETS as appropriate.

This ETS describes measurements for operating frequency range(s), effective radiated power and power density as well as spurious emissions for transmitters and receivers.

The measurement methods have been adapted from ETR 027 [4] where possible.

This ETS specifies test site characteristics, test conditions, equipment calibration and methods of

measurement. This ETS is a general standard which may be superseded by specific standards covering specific applications.

Additional standards or specifications may be required for equipment such as that intended for connection to the Public Switched Telephone Network (PSTN) and/or other Public Data Networks (PDN).

EN 300 328-2 Ver. 1.1.1(2000-07) Electromagnetic compatibility and Radio Spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive.

This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

The present document is part 2 of a multi-part EN covering the Electromagnetic compatibility and Radio Spectrum Matters (ERM); Wideband Transmission systems; data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques, as identified below:

Part 1: "Technical characteristics and test conditions";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".

The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [6] laying down a procedure for the provision of information in the field of technical standards and regulations.

The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive").

National transposition dates

Date of adoption of this EN: 21 July 2000
Date of latest announcement of this EN (doa): 31 October 2000
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2001
Date of withdrawal of any conflicting National Standard (dow): 30 April 2001

Scope

The present document applies to the following radio transceivers, transmitters and receivers:

Fixed, mobile or portable equipment and plug-in radio devices utilizing wideband radio modulation techniques and aggregate bit rates in excess of 250 kbits/s. The equipment shall have an effective radiated power of up to -10 dBW (100 mW) and a power density of up to -10 dBW (100 mW) e.i.r.p. per 100 kHz for frequency hopping spread spectrum modulation or a power density of up to -20 dBW (10 mW) e.i.r.p. per 1 MHz for other forms of spread spectrum modulation.

This radio equipment is capable of operating in all or any part of the frequency band shown in table 1.

Table 1: Industrial, Scientific and Medical (ISM) service frequency band
Direction of transmission Industrial, Scientific and Medical (ISM) service frequency band
Transmit / Receive 2,4 GHz to 2,483 5 GHz

Equipment using modulation techniques different from those defined in EN 300 328-1 [4], subclauses 5.1.1 and 5.1.2 do not fall within the scope of the present document.

The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) Article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".

In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of Article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.

NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Draft EN 300 330 - 1 V1.3.1 (2001-06) ElectroMagnetic Compatibility and Radio Spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz;

Part 1: Technical characteristics and test methods

Foreword

This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

For non EU countries the present document may be used for regulatory (Type Approval) purposes.

The present document is part 1 of a multi-part deliverable covering the Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz, as identified below:

Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 15 June 2001
Date of latest announcement of this EN (doa): 30 September 2001
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2002
Date of withdrawal of any conflicting National Standard (dow): 31 March 2002

Scope

The present document applies to Short Range Devices (SRDs) transmitters and receivers:
a) - transmitters operating in the range from 9 kHz to 25 MHz; and - inductive loop transmitters operating from 9 kHz to 30 MHz;
b) - receivers operating from 9 kHz to 30 MHz.

The present document contains the technical characteristics for radio equipment and is referencing in CEPT/ERC Recommendation 70-03 [3] and ERC Decisions.

The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It is a product family standard which may be completely or partially superseded by specific standards covering specific applications.

The present document applies to generic SRDs:
- inductive loop systems;
- with an antenna connection and/or with an integral antenna;
- for alarms, identification systems, telecommand, telemetry, etc.;
- applications with or without speech.

When selecting parameters for new SRDs, which may have inherent safety of human life implications, manufacturers and users should pay particular attention to the potential for interference from other systems operating in the same or adjacent bands.

The present document covers fixed stations, mobile stations and portable stations. If a system includes transponders, these are measured together with the transmitter.

All types of modulation for radio devices are covered by the present document, provided the requirements of clause 7.3 are met.

The radio equipment, covered by the classification SRD is divided into several power classes based on maximum radiated field strength or output power (see table 1). The power class designation is based on CEPT/ERC Recommendation 70-03 [3] and ERC Decisions.

Table 1: Maximum radiated H-field or power (e.i.r.p)
Power Class Radiated H-field or power level
1 7 dBµA/m at 10 m
2 42dBµA/mat10m
3 72dBµA/mat10m (at 9 kHz to 30 kHz, descending 3 dB/octave from 30 kHz 135 kHz)
4 37,7 dBµA/m at 10 (at 135 kHz, descending 3 dB/octave from 135 kHz to 1 MHz) 29 dBµA/m at 10 m (at 1,0 MHz descending 9 dB/oct from 1 MHz to 4,642 MHz)
5 9 dBµA/m at 10 m (4,642 MHz to 30 MHz)

On non-harmonized parameters, national administrations may impose conditions on the type of modulation, frequency, channel/frequency separations, maximum transmitter radiated field strength/maximum output current to a defined antenna, duty cycle, equipment marking and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an individual or general licence, or as a condition for use under licence exemption.

Three types of measuring methods are defined in the present document due to the varied nature of the types of equipment used in this band. One method measures the RF carrier current, another measures the radiated H-field and the third the conducted power.

The present document covers requirements for radiated emissions below as well as above 30 MHz.

Additional standards or specifications may be required for equipment such as that intended for connection to the Public Switched Telephone Network (PSTN).

EN 300 330-2 Ver. 1.1.1 (2001-07) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz;
Part 2: Harmonized EN under article 3.2 of the R&TTE Directive

Foreword

This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [5] laying down a procedure for the provision of information in the field of technical standards and regulations.

The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive").

The present document is part 2 of a multi-part deliverable covering the Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz, as identified below:

Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 15 June 2001
Date of latest announcement of this EN (doa): 30 September 2001
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2002
Date of withdrawal of any conflicting National Standard (dow): 31 March 2003

Scope

The present document applies to Short Range Devices (SRDs) transmitters and receivers:
- transmitters operating in the range from 9 kHz to 25 MHz and inductive loop transmitters operating from 9 kHz to 30 MHz;
- receivers operating in the range from 9 kHz to 30 MHz.
The present document applies to SRDs:
- either with a Radio Frequency (RF) output connection and specified antenna, or with an integral antenna;
- for alarms, identification systems, radio-determination, telecommand, telemetry etc. applications;
- for all types of modulation;
- with or without speech.

The present document covers fixed stations, mobile stations and portable stations. If a system includes transponders, these are measured together with the transmitter.

All types of modulation for radio devices are covered by the present document, provided the requirements of clause 4.1.2 is met.

The radio equipment, covered by the classification SRD is divided into several power classes based on maximum radiated field strength or power (see table 1). The power class designation is based on CEPT/ERC Recommendation 70-03 [3] or relevant ERC Decisions.

Table 1: Maximum radiated H-field or power (e.i.r.p)
Power Class Radiated H-field or power level
1 7 dBµA/m at 10 m
2 42dBµA/mat10m
3 72dBµA/mat10m (at 9 kHz to 30 kHz, descending 3 dB/octave from 30 kHz to 135 kHz
4 37,7 dBµA/m at 10 m (at 135 kHz, descending 3 dB/octave from 135 kHz to 1 MHz) 29 dBµA/m at 10 m (at 1,0 MHz descending 9 dB/oct from 1 MHz to 4,642 MHz)
5 9 dBµA/m at 10 m (4,642 MHz to 30 MHz)

On non-harmonized parameters, national administrations may impose conditions on the type of modulation, frequency, channel/frequency separations, maximum transmitter output power/effective radiated power, duty cycle, equipment marking and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an individual or general licence, or as a condition for use under licence exemption.

The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile.

The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [1] article 3.2, which states that "…radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".

In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] may apply to equipment within the scope of the present document.

NOTE: A list of such ENs is included on the web site: http://www.newapproach.org/.

EN 300 440 - 1: (2001-09) Electromagnetic compatibility and Radio spectrum Matters (ERM);Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range;

Part 1: Technical characteristics and test methods

Foreword

This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

For non EU countries the present document may be used for regulatory (Type Approval) purposes.

The present document is part 1 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range, as identified below:

Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 7 September 2001
Date of latest announcement of this EN (doa): 31 December 2001
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2002
Date of withdrawal of any conflicting National Standard (dow): 30 June 2002

Scope

The present document applies to Short Range Devices (SRDs) transmitters and receivers:
a) transmitters operating in range from 1 GHz to 40 GHz with power levels ranging up to 4W;
b) receivers operating in the range from 1 GHz to 40 GHz;

The present document contains the technical characteristics for radio equipment and is referencing CEPT/ERC Recommendation for SRDs CEPT/ERC Recommendation 70-03 [1] and ERC Decisions.

The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It is a product family standard which may be completely or partially superseded by specific standards covering specific applications.

The present document applies to generic SRDs:
- either with a Radio Frequency (RF) output connection and specified antenna, or with an integral antenna;
- for alarms, identification systems, radio-determination, telecommand, telemetry etc. applications;
- for all types of modulation;
- with or without speech.

When selecting parameters for new SRDs, which may have inherent safety of human life implications, manufacturers and users should pay particular attention to the potential for interference from other systems operating in the same or adjacent bands.

The present document covers fixed stations, mobile stations and portable stations. If a system includes transponders, these are measured together with the transmitter.

All types of modulation for radio devices are covered by the present document, provided the requirements of clause 7.2 are met.

The radio equipment, covered by the classification SRD is divided into several power classes based on maximum output power (see table 1). The power class designation is based on CEPT/ERC Recommendation 70-03 [1] or ERC Decisions.

Table 1: Maximum radiated peak power (e.i.r.p.)
Power Class (see note 1)
Power level (conducted or radiated)
8 10 mW
9 25 mW
11 100 mW
12 500 mW (see note 2)
13 1 W
14 2 W
14a 4 W (see note 2)
NOTE 1: Class designation is based on CEPT/ERC
Recommendation 70-03 [1].
NOTE 2: For RFID applications, see annex C of the present document.

On non-harmonized parameters, national administrations may impose conditions on the type of modulation, frequency, channel/frequency separations, maximum transmitter radiated field strength/maximum output current to a defined antenna, duty cycle, equipment marking and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an individual or general licence, or as a condition for use under licence exemption.

The present document does not require measurements for radiated emissions below 25 MHz.

EN 300 440-2 Ver. 1.1.1 (2001-09) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive

Foreword

This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM).

The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [2] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations.

The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive").

The present document is part 2 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range, as identified below:

Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 7 September 2001
Date of latest announcement of this EN (doa): 31 December 2001
Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2002
Date of withdrawal of any conflicting National Standard (dow): 30 June 2003

Scope

The present document applies to Short Range Devices (SRDs) transmitters and receivers:
- transmitters operating in range from 1 GHz to 40 GHz with power levels ranging up to 4W;
- receivers operating in the range from 1 GHz to 40 GHz.

The present document contains the technical characteristics for radio equipment and is referencing CEPT/ERC Recommendation for SRDs CEPT/ERC Recommendation 70-03 [5].

The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. It is a product family standard which may be completely or partially superseded by specific standards covering specific applications.

The present document applies to generic SRDs:
- either with a Radio Frequency (RF) output connection and specified antenna, or with an integral antenna;
- for alarms, identification systems, radio-determination, telecommand, telemetry etc. applications;
- for all types of modulation;
- with or without speech.

The present document covers fixed stations, mobile stations and portable stations. If a system includes transponders, these are measured together with the transmitter.

The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile.

All types of modulation for radio devices are covered by the present document, provided the requirements of clause 4.1.2 are met.

The radio equipment, covered by the classification SRD is divided into several power classes based on maximum output power (see table 1). The power class designation is based on CEPT/ERC Recommendation 70-03 [5].

Table 1:
Maximum radiated peak power (e.i.r.p.)
Power Class Power level (conducted or radiated)

8 10 mW
9 25 mW
11 100 mW
12 500 mW (see note 1)
13 1 W
14 2 W
14a 4 W (see note 1)

NOTE 1: For RFID applications, see annex C of Part 1 of this standard.

The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [1] (R&TTE Directive), see annex E of EN 300 440-1 [3].

In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] may apply to equipment within the scope of the present document.

NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Other documents that may be of interest to RFID are found on the ETSI server.